Jvc кассетная автомагнитола ks f525

Инструкция и руководство для
JVC KS-F525 RU на русском на английском

30 страниц подробных инструкций и пользовательских руководств по эксплуатации

Подключаем AUX к магнитоле JVC KD-G511

обзор усилителя jvc ks — ax4302

Новинки от JVC. Новый модельный ряд. Бюджетные модели JVC. Автомагнитолы.

Автомагнитола JVC KD-X362BT

Автомагнитола JVC (мелкий ремонт)

Автомагнитола JVC KD-X151

CASSETTE RECEIVER РЕСИВЕР С КАССЕТНЫМ ПРОИГРЫВАТЕЛЕМ ENGLIS.

Instructions, Cassette receiver, Ресивер с кассетным проигрывателем

РЕСИВЕР С КАССЕТНЫМ ПРОИГРЫВАТЕЛЕМ

ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ

В соответствии с Законом Российской Федерации “О защите прав

потребителей” срок службы (г одности) данного товара “по истечении
которого он может представлять опасность для жизни, здоровья
потребителя, причинять вре д его имуществу или окружающей сре де”
составляет семь (7) лет со дня произво дства. Этот срок является
временем, в течение которого потребитель данног о товара может
безопасно им пользова ться при у словии соблю дения инструкции по
эк сплуатации данного товара, проводя необходимое обслуживание,
включающее замену р асходных ма териалов и/или соответствующее
ремонтное обеспечение в специализированном сервисном центре.

Дополнительные к осметические материалы к данному товар у,

поставляемые вместе с ним, могут хр аниться в течение дв ух (2) лет со
дня его производства.

Срок службы (г одности), кроме срока хранения дополнительных

косметических материалов, упомянутых в пре дыдущих дв ух пунктах, не
затрагивает никаких других прав потребителя, в частности, гарантийного
свидетельства JV C, которое он может получить в соответствии с зак оном
о правах потребителя или других законов, связанных с ним.

For installation and
connections, refer to the
separate manual.
Указания по установке
и выполнению
соединений приводятся
в отдельной
инструкции.

ENGLISH Thank you for purchasing a JVC product. Please read.

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

LOCATION OF THE BUTTONS .

Turning on the power .

RADIO BASIC OPERATIONS .

Listening to the radio .

Storing stations in memory .

Tuning in to a preset station .

Scanning broadcast stations

(only for KS-F525) .

RDS OPERATIONS . 10
(

only for KS-FX725R

What you can do with RDS .

Other convenient RDS functions and

TAPE OPERATIONS . 16

Listening to a cassette .

Finding the beginning of a tune .

Other convenient tape functions .

SOUND ADJUSTMENTS . 19

Adjusting the sound .

Turning on/off loudness function

(only for KS-F525) .

Using the sound control memory .

Storing your own sound adjustments .

OTHER MAIN FUNCTIONS . 23

Setting the clock .

Changing the general settings (PSM) .

Detaching the control panel .

CD CHANGER OPERATIONS . 27
(

only for KS-FX725R

Selecting CD playback modes .

EXTERNAL COMPONENT OPERATIONS .. 29
(

only for KS-FX725R

Playing an external component .

DAB TUNER OPERATIONS . 30
(

only for KS-FX725R

Tuning in to an ensemble and one of the

Storing DAB services in memory .

Tuning in to a preset DAB service .

How to reset your unit

Press and hold both the SEL (select) and

(standby/on/attenuator) buttons at the same

time for several seconds.
This will reset the built-in microcomputer.

Your preset adjustments – such as preset channels or
sound adjustments – will also be erased.

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

Temperature inside the car.

If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.

Location of the buttons, Control panel―ks-fx725r, Control panel—ks-fx725r

English, Display window

LOCATION OF THE BUTTONS

DISP (display) button

TP (traffic programme)
RDS (radio data system) button

PTY (programme type) button

• Also functions as the DAB button.

• Also functions as SSM buttons when pressed

SEL (select) button

RPT (repeat) button

• Also functions as

∞ (DAB service selection).

RND (random) button

• Also functions as

5 (DAB service selection) or

SCM (sound control memory) button

CD-CH (CD changer) button

(control panel release) button

Volume (or audio) level indicator

SCM (sound control memory) indicator

Tuner reception indicators
MO (monaural), ST (stereo)

RND (random) indicator

RPT (repeat) indicator

LOUD (loudness) indicator

FM band number indicators
FM1, FM2, FM3

Sound mode indicators
BEAT, SOFT, POP

RDS indicators
AF, EON, REG, TP, PTY

CD-CH (CD changer) indicator

AM band indicator

Control panel―ks-f525, Location of the buttons, Control panel—ks-f525

LOCATION OF THE BUTTONS

LOUD (loudness) button

DISP (display) button

• Also functions as SSM buttons when pressed

SEL (select) button

RPT (repeat) button

MO (monaural) button

SCM (sound control memory) button

(control panel release) button

Volume (or audio) level indicator

SCM (sound control memory) indicator

Tuner reception indicators
MO (monaural), ST (stereo)

RPT (repeat) indicator

LOUD (loudness) indicator

FM band number indicators
FM1, FM2, FM3

Sound mode indicators
BEAT, SOFT, POP

AM band indicator

Basic operations, Turning on the power, Turning on the power 1

Adjust the volume.

Adjust the sound as you want.
(See pages 19 – 22.)

To drop the volume in a moment

briefly while listening to any

source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
• If you turn the control dial clockwise, you can

also restore the sound.

To turn off the power

until “SEE YOU” appears

When you use this unit for the first time, set the built-in
clock correctly, see page 23.

To decrease the volume.

To increase the volume.

Volume level appears.

Volume level indicator

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.

Select the source.

To operate the tuner (FM or AM),

see pages 6 – 15.

To operate the tape,

see pages 16 – 18.

Only for KS-FX725R:
To operate the CD changer,

see pages 27 – 28.

To operate the external component,

To operate the DAB tuner,

see pages 30 – 33.

Radio basic operations, Listening to the radio, Searching a station automatically: auto search

RADIO BASIC OPERATIONS

Listening to the radio

You can use either automatic searching or manual
searching to tune in to a particular station.

Searching a station automatically:
Auto search

Select the band (FM1 – 3, AM).

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.

Start searching a station.

When a station is received, searching stops.

To stop searching before a station is received,
press the same button you have pressed for
searching.

FM1 and FM2 : 87.5 MHz – 108.0 MHz
FM3 : 65 MHz – 74 MHz

stations of higher
frequencies.

stations of lower
frequencies.

Audio (see page 25) or
volume level indicator

Selected band appears.

Searching a station manually: manual search

Searching a station manually:
Manual search

Select the band (FM1 – 3, AM).

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.

“M (manual)” starts flashing on the
display.

Lights up when receiving
an FM broadcast in stereo.

Selected band appears.

Tune in to a station you want while “M”
is flashing.

• If you release your finger from the button,

the manual mode will automatically turn off
after 5 seconds.

• If you hold down the button, the frequency

keeps changing (in 50 kHz intervals (87.5
MHz – 108 MHz), in 30 KHz intervals (65
MHz – 74 MHz) for FM and 9 kHz intervals
for AM – MW/LW) until you release the
button.

When an FM stereo broadcast is hard to
receive:

Press MO RND (for KS-FX725R) or MO (for KS-
F525) while listening to an FM stereo broadcast.
• Each time you press the button, the MO

indicator lights up and goes off alternately.

When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved (the ST indicator
goes off).

To restore the stereo effect, press the same
button again.

in to stations of lower
frequencies.

in to stations of higher
frequencies.

Storing stations in memory

Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3).
These stations are preset in the number buttons —
No.1 (lowest frequency) to No.6 (highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.

You can preset up to 6 stations in each band (FM1,
FM2, FM3 and AM) manually.

Ex.: Storing an FM station of 88.3 MHz into the

preset number 1 of the FM1 band

Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).

Storing stations in memory

You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM band
(FM1, FM2 and FM3).

Select the FM band (FM1 – 3) you want
to store FM stations into.

Press and hold both buttons for more
than 2 seconds.

“SSM” appears, then disappears when automatic
preset is over.

Tuning in to a preset station, Scanning broadcast stations

Tuning in to a preset station

You can easily tune in to a preset station.
Remember that you must store stations first. If you
have not stored them yet, see “Storing stations in
memory” on pages 8 and 9.

Select the band (FM1 – 3, AM).

Select the number (1 – 6) for the preset
station you want.

Scanning broadcast stations

(only for KS-F525)

When you press SCAN while listening to the
radio, station scanning starts.

Each time a broadcast is tuned
in, scanning stops for about 5
seconds (tuned frequency
number flashes on the display),
and you can check what program
is now being broadcast.

If you want to listen to that program, press the
same button again to stop scanning.

Tune in to a station (in this example,
of 88.3 MHz).

Press and hold the number button
(in this example, 1) for more than 2
seconds.

Repeat the above procedure to store
other stations into other preset
numbers.

• A previously preset station is erased when a new station

is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example, during
battery replacement). If this occurs, preset the stations
again.

“P 1” flashes for a few seconds.

in to stations of lower
frequencies.

in to stations of higher
frequencies.

Rds operations, What you can do with rds

To use Network-Tracking Reception, press and
hold TP RDS (Traffic Programme/Radio Data
System) for more than 1 second. Each time you
press and hold the button, Network-Tracking
Reception modes change as follows:

Mode 1
The AF indicator lights up but the REG indicator
does not.
Network-Tracking Reception is activated with
Regionalization set to “off.”
Switches to another station within the same
network when the receiving signals from the
current station become weak.

In this mode, the programme may differ from the one
currently received.

Mode 2
Both the AF indicator and the REG indicator light
up.
Network-Tracking Reception is activated with
Regionalization set to “on.”
Switches to another station, within the same
network, broadcasting the same programme
when the receiving signals from the current
station become weak.

Mode 3
Neither the AF indicator nor the REG indicator
lights up.
Network-Tracking Reception is deactivated.

This section is only for KS-FX725R.

What you can do with RDS

RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations send
their station names, as well as information about
what type of programme they broadcast, such as
sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” The EON indicator
lights up while receiving an FM station with the
Enhanced Other Networks data. By using the
Enhanced Other Networks data sent from a station,
you can tune in to a different station of a different
network broadcasting your favorite programme or
traffic announcement while listening to another
programme or to another source such as tape.

By receiving the RDS data, this unit can do the
following:
• Tracing the same programme automatically

• Standby Reception of TA (Traffic

Announcement) or your favorite programme

• PTY (Programme Type) search
• Programme search
• And some other functions

Tracing the same programme
automatically (Network-Tracking
Reception)

When driving in an area where FM reception is not
good, the tuner built in this unit automatically tunes
in to another RDS station, broadcasting the same
programme with stronger signals. So, you can
continue to listen to the same programme in its
finest reception, no matter where you drive. (See
the illustration on the next page.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly — PI
(Programme Identification) and AF (Alternative
Frequency).
Without receiving these data correctly from the RDS
station you are listening to, Network-Tracking
Reception will not operate.

Источник